UPH Laptop Tester- CPU Centrino 4 generation. 478 false CPU load tester

Allows Parallel DB25 compliant printer to connect to your laptop or desktop w/ PCMCIA Slot conveniently and easily.

• Compliant with IEEE 1284.
• Compliant with PCMCIA 32bit CardBus specification.
• Supports up to 1.5 Mbytes/sec transfer rate.
• One end is PCMCIA type II interface, which is compatible with PCMCIA type II/III slot.
• Compatible with Windows 98/98SE/ME/2000/NT/XP/Vista/Linux.

• Note: The adapter supports printer only.

• Support two types speed (MLC &SLC) CF card, suits only 1CF card
• Support Windows 7 CR-1000 IDE by inserting a CF (4GB~64GB).
• Large capacity but with only 1.8 inch light case of IDE to SSD adapter.
• DOS/WinCE/Linux/WinXP/Vista/Win7 bootable.

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel 975 chipset Motherboard

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel i945 chipset Motherboard

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel i915 chipset Motherboard

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboa

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel i3/i5/i7 CPU Motherboard

Allows RS-232 compliant peripheral to connect to your laptop or desktop w/ ExpressCard Slot conveniently and easily.
Works with various types of RS232 serial devices including modems, PDAs, label printers, bar code scanners, digital cameras, and more

• Compliant with ExpressCard/34mm Type II standard.
• Compatible with standard 34mm & 54mm ExpressCard slot.
• Support standard RS-232 serial interface.
• Support software / hardware RS-232 flow control.
• Software programmable baud rate up to 3Mbps.
• Date transfer rate up to 921.6KB/s.
• Compatible with USB2.0 full speed (12Mbps) throughput.
• Plug & play and hot swapping capability.

• Supports Windows 98SE, ME, 2000, XP, Server 2003, Vista, Windows 7, Server 2008, WinCE 4.2-5.2 & Mac OS 8/9 & Linux RedHat 7.3/8.0/9.0 Only & Linux Kernel  2.4.10 and above.

Features:

• Two 6-Pin 1394A Ports
• IEEE 1394-1995 standard compliant for high performance serial bus and P1394A Supplement 4.0
• 1394 Open HCI specification V1.0 and V1.1 Compliant
• Data transfer rate: 100/200/400 Mbps supported
• Compatible to 1-Lane(X1)PCI -Express throughpu
• 12VDC Adapter for high current consumption devices (Optional)
• Fully Plug&Play and Hot Play compatible
• Driver supported MS Windows 2000/XP/XP 64-bit/Vista and MAC OS X supported

Package Includes:

• 1 x IEEE1394A ExpressCard
• 1 x Cable

• Compliant with PCI Express Base Specification, Revision 1.1
• SuperSpeed (5.0Gbps) additional
• USB 3.0 will offer a myriad of possibilities for applications requiring fast and high-capacity communication, while maintaining compatibility with USB 2.0
• Driver supported MS Windows 98SE/ME/2000/XP/Server 2003/XP 64-bit/Vista/win7

Product Description

• Compliant with USB3.0, will be entirely support USB2.0 Maximum transmission speed 5Gbps.
• Support 2 downstream ports for all speeds.
• 100% functional testing to ensure product quality.
• Power input: DC 5V 2A.

*This model is a switching-mode power supply, operation at input AC voltage 95V to 265V and DC voltage of 12-19V/4.5A max, 20-24V/3.5A max, with many protection functions for notebook use.

Model: LP-90W
INPUT   : 110-240V~ 50/60Hz, 1.3A Max.
OUTPUT: 12/15/16/18/19V       4.5A Max.
            : 20-24V                     3.5A Max.

Universal DC Connector tie-in size:

1. 4.3 x 6.0 mm (Pin)
2. 3.0 x 6.3 mm
3. 2.5 x 5.5 mm
4. 2.1 x 5.5 mm
5. 1.7 x 5.5 mm
6. 3.3 x 5.0 mm (Pin)
7. 1.7 x 4.8 mm
8. 1.7 x 4.0 mm

Package Contents:

-  12-24V 90W AC/DC Adapter
- 2 Round-pin AC Power Cord
- 8 different sizes DC Connector Tip

*Plsease take note, make sure that the polarity of DC connector plug is connected correctly, select output voltage to suit to laptop before use.

Laptop Mainboard Board DDR RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected  by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light

Laptop POST CODE Testing Card

• Supports three bus interfaces: MINI PCI, Mini PCI-E and LPC.
• Support LCD diaplay for English ( English Manuelincluded)
• Support IBM laptop battery interface
• Support Asus laptop ELPC interface

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• It can diagnosis signal which show the problem of CPU, Memory, display card and so on.
• The Display portion is composed with two 7-segment LEDs. The two "Dots" of the LEDs are used to indicate the notebook "RST" and "CLK" status. The left side "Dot" is for "RST", and the right side "Dot" is for "CLK".
• When the notebook is in "Reset" status, the left side Dot" will be lighted. And when the notebook has a correct CLK output, the right side "Dot" will be lighted.

Note: Please be aware that Mini-PCI-E is supported with limitation model of notebook, and the pin orientation must follow to PIN1-3.3V, PIN2-LFRAME#, PIN3-LAD3, otherwise, it need to test with other port, such as LPC or mini-pci.

The tester diagnose and analy the mother board,CPU and VGA card.
No need software.

• Run the tester and refer the number code to the manuel for the fault the code indicates.
  

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.
• USB port for power, 25 pin parallel printer port LPT for debug.

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.
• USB port for power, 10 pin port LPT for debug.

Laptop POST CODE Testing Card

• Supports three bus interfaces: MINI PCI, Mini PCI-E and LPC.
• Support LCD diaplay for English ( English User Guide included)

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• It can diagnosis signal which show the problem of CPU, Memory, display card and so on.
• The Display portion is composed with two 7-segment LEDs. The two "Dots" of the LEDs are used to indicate the notebook "RST" and "CLK" status. The left side "Dot" is for "RST", and the right side "Dot" is for "CLK".
• When the notebook is in "Reset" status, the left side Dot" will be lighted. And when the notebook has a correct CLK output, the right side "Dot" will be lighted.

Note: Please be aware that Mini-PCI-E is supported with limitation model of notebook, and the pin orientation must follow to PIN1-3.3V, PIN2-LFRAME#, PIN3-LAD3, otherwise, it need to test with other port, such as LPC or mini-pci.

Laptop POST CODE Testing Card

• Supports three bus interfaces: MINI PCI, Mini PCI-E and LPC.
• Support LCD diaplay for English ( English User Guide included)

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• It can diagnosis signal which show the problem of CPU, Memory, display card and so on.
• The Display portion is composed with two 7-segment LEDs. The two "Dots" of the LEDs are used to indicate the notebook "RST" and "CLK" status. The left side "Dot" is for "RST", and the right side "Dot" is for "CLK".
• When the notebook is in "Reset" status, the left side Dot" will be lighted. And when the notebook has a correct CLK output, the right side "Dot" will be lighted.

Note: Please be aware that Mini-PCI-E is supported with limitation model of notebook, and the pin orientation must follow to PIN1-3.3V, PIN2-LFRAME#, PIN3-LAD3, otherwise, it need to test with other port, such as LPC or mini-pci.

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.
• USB port for power, 25 pin parallel printer port LPT for debug.

This tester is made specially for diagnose the fault of IBM laptop, apply to IBM laptop  Model:

•   T61, R61/I/E, T400/S, T500, X61/S, X200/S, W500, W700 series.

• Run the tester and refer the number code (result of Post) to the error code listed as below:

FF 00- CPU is not working, bios programme corrupted or no bios posting.
2C 28 2E 38- memory error, memory cicuit error, north bridge error.
4A- display card error.
49 55 90- South bridge error.
B6- bios is looked.

Laptop Mainboard Board DDR 2 RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light

Laptop Mainboard Board DDR RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected  by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.

5pcs  PCI DDR1/2/3 SD Dummy Load for Laptop Motherboard repair

1pcs  MINI-PCI   Laptop  Dummy load
1pcs  DDR          Laptop  Dummy load
1pcs  DDR2        Laptop  Dummy load
1pcs  DDR3        Laptop  Dummy load
1pcs  SD           Laptop  Dummy load

Suit for the laptop and desktop which of POST code output to LPT, can access to USB or access to computer power　

4-digit display. "Star Code" is "0000"or"FFFF".Can test itself faults, fully compatible 286 to PIV motherboards, the code is nore exact, and reliable. no crash. Can check the code, the code won't pass when it appears, press switch once, then display a code and pause.

Laptop Mainboard Board DDR 3 RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light