Laptop Spare Part

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel i945 chipset Motherboard

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel 975 chipset Motherboard

CPU load tester (mother board)

Description:
It is used to test each point and voltage of CPU is correct or not. After confirmed ok, then install genius CPU to avoid burn CPU down during repairing motherboard.

Application:
Intel i3/i5/i7 CPU Motherboard

5pcs  PCI DDR1/2/3 SD Dummy Load for Laptop Motherboard repair

1pcs  MINI-PCI   Laptop  Dummy load
1pcs  DDR          Laptop  Dummy load
1pcs  DDR2        Laptop  Dummy load
1pcs  DDR3        Laptop  Dummy load
1pcs  SD           Laptop  Dummy load

Laptop Mainboard Board DDR RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected  by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light

Laptop Mainboard Board DDR RAM Memory Slot tester.

• Through the process of starting up and read the RAM Memory, could indicate the faults in the mother board circuit for further repairing.
• The fault could be reflected  by the LED light, indicating open circuit or short circuit or data line and address line.

Usage:

• Install the 3.3v (CR2032) battery on the tester, mainboard need not power on, press the button of the tester.
• If the LEDs all light on and the brightness are all the same, the signal is all right ,there is no problem.
• No light Or weak light signal there is problem, you should refer to sign indication beside that LED light

Laptop POST CODE Testing Card

• Supports three bus interfaces: MINI PCI, Mini PCI-E and LPC.
• Support LCD diaplay for English ( English Manuelincluded)
• Support IBM laptop battery interface
• Support Asus laptop ELPC interface

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• It can diagnosis signal which show the problem of CPU, Memory, display card and so on.
• The Display portion is composed with two 7-segment LEDs. The two "Dots" of the LEDs are used to indicate the notebook "RST" and "CLK" status. The left side "Dot" is for "RST", and the right side "Dot" is for "CLK".
• When the notebook is in "Reset" status, the left side Dot" will be lighted. And when the notebook has a correct CLK output, the right side "Dot" will be lighted.

Note: Please be aware that Mini-PCI-E is supported with limitation model of notebook, and the pin orientation must follow to PIN1-3.3V, PIN2-LFRAME#, PIN3-LAD3, otherwise, it need to test with other port, such as LPC or mini-pci.

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.
• USB port for power, 10 pin port LPT for debug.

The tester diagnose and analy the mother board,CPU and VGA card.
This card is also called POST( Power on self test ) Card.
No need software.

• Run the tester and refer the number code (result of Post) to the error code table in the User Guide for the fault the code indicates.
• Especially when the PC can't boot operating system, or blank screen, or the card and motherboard couldn't issue an audible beep.
• Work on desktop or laptop computers.

Suit for the laptop and desktop which of POST code output to LPT, can access to USB or access to computer power　

4-digit display. "Star Code" is "0000"or"FFFF".Can test itself faults, fully compatible 286 to PIV motherboards, the code is nore exact, and reliable. no crash. Can check the code, the code won't pass when it appears, press switch once, then display a code and pause.